Does Canon waterproof camera & lens protection cases have PFAS?
We graded 8 Canon waterproof camera & lens protection cases products, averaging Excellent (85/100). 8 of them grade Good or better. Against the other 30 waterproof camera & lens protection cases brands we grade, where the middle brand sits at 68/100, Canon is better than typical, scoring above 82% of them.
PFAS Authority is a scoring system, not a laboratory. We do not test products ourselves. Grades are model-based, built from published ingredients, materials, certifications, brand disclosures and third-party lab results where they exist. See the rubric.
Canon waterproof camera & lens protection cases worth buying Good or better, best-graded first
Canon
WP-DC55 Waterproof Case for G7 X Mark II
Polycarbonate housing, rubber seals
Rubber seal degradation and water intrusion
Synthetic rubber seals degrade from heat, UV, saltwater, and age (typically 5-7 years).…
Polycarbonate yellowing and embrittlement
Polycarbonate housing can yellow and become brittle under prolonged UV exposure or high…
No coating described, and no PFAS statement from the brand.
⚠Brand says nothing about PFAS
Canon
WP-DC1 Waterproof Case
Polycarbonate
Polycarbonate stress-cracking and degradation
Polycarbonate is susceptible to damage from UV exposure, impact, and contact with certain…
Gasket and seal material degradation
The WP-DC1 uses rubber or silicone gaskets to maintain the waterproof seal. These…
No coating described, and no PFAS statement from the brand.
⚠Brand says nothing about PFAS
Canon
WP-DC17 Waterproof Case for Camera
Rubber, polycarbonate
Rubber gasket degradation over time
Natural and synthetic rubber seals can harden, crack, or lose elasticity with age, UV…
Mold or bacterial growth inside sealed case
If moisture enters through a compromised seal or if the case is sealed while damp, mold…
No coating described, and no PFAS statement from the brand.
⚠Brand says nothing about PFAS
Canon
Marine Waterproof Camera Case
Waterproof case, likely polyurethane or nylon
Polyurethane degradation and off-gassing
Long-term polyurethane exposure to UV, heat, or high humidity can break down the polymer…
Nylon fiber shedding or microplastic release
If the case includes nylon webbing straps or lining, mechanical wear or rubbing against…
Zipper metal or fastener corrosion
Metal zippers and clips can corrode if exposed to salt water or chlorine without rinsing.…
No coating described, and no PFAS statement from the brand.
⚠Brand says nothing about PFAS
Canon
WP-DC5 Waterproof Case
Polycarbonate case with waterproof seals
Polycarbonate degradation under UV and heat
Polycarbonate is susceptible to UV degradation and loss of clarity over 5-10 years of…
Gasket and seal material leachates
Seals are typically made from rubber or synthetic elastomer compounds that may contain…
Bacterial or mold growth in seals if not maintained
Trapped moisture in gasket crevices can foster bacterial or fungal growth if the case is…
No coating described, and no PFAS statement from the brand.
⚠Brand says nothing about PFAS
Canon
WP-DC43 Underwater Camera Housing
Polycarbonate housing, rubber seals
Polycarbonate structural degradation (optical clarity loss)
Polycarbonate yellows and becomes cloudy over 5-10 years with UV exposure and temperature…
Rubber seal degradation and water ingress
Nitrile and EPDM seals degrade through chlorine exposure, salt crystallization, and…
Microplastic shedding from seals during use
Nitrile and EPDM seals may shed microscopic particles during compression cycles in deep…
No coating described, and no PFAS statement from the brand.
⚠Brand says nothing about PFAS
Canon
WP DC200 Marine Camera Case
Waterproof synthetic case
Plastic leaching (thermal stress)
Synthetic polymer casings can soften or release minor oligomers if stored in hot vehicles…
Mold and microbial growth (internal)
If gaskets are not fully sealed or case is stored wet, trapped moisture can support mold…
No coating described, and no PFAS statement from the brand.
⚠Brand says nothing about PFAS
Canon
WP-DC20 Waterproof Case for Powershot S1 IS
Polycarbonate/urethane case with waterproof seals
Polycarbonate stress-cracking and microplastic risk
Polycarbonate can develop fine cracks or stress lines after years of UV exposure or…
Polyurethane gasket degradation
Polyurethane O-rings and seals can harden, shrink, or lose elasticity after 5-10 years…
No coating described, and no PFAS statement from the brand.
⚠Brand says nothing about PFAS
See every Canon product we grade on the Canon brand page, or the full waterproof camera & lens protection cases ranking.